Main Page | Recent changes | View source | Page history

Printable version | Disclaimers | Privacy policy | Latest revision

Not logged in
Log in | Help
 

How To: Lap a Heatsink

Revision as of 13:16, 25 March 2007 by Agg (Talk | contribs)

Just thought I'd share some of the information I've got from lapping a few heat sinks. Hope you find it useful.


If you're reading this guide you probably already know the benefits of lapping a heat sink but I'll go over it anyway.

Most heat sinks that you buy these days have a rather rough base on them. They are mostly flat, but not always, so by lapping them you get the benefit of a smoother surface resulting in better heat transfer, as well as making sure that your surface is flat.

The heat sink I'll be using in this guide is a good example. This is what it looked like straight out of the box.


http://slidog.bigblog.com.au/data/2/11934/image/STstockbase7064720061109205005.jpg


It looks ok but have a look at what happens to the themal paste when mounted.


http://slidog.bigblog.com.au/data/2/11934/image/thermalpastuneven6968320061109200734.jpg


You'll notice that it's thicker at the sides because the base of the heat sink is not flat.



Lapping


You'll need: A heat sink, CPU, etc. Some wet-dry sandpaper of 200, 400, 800, 1200 and 2000 grit. A flat glass surface to work on. A roll of duct tape. An old rag. A couple of hours of time.


http://slidog.bigblog.com.au/data/2/11934/image/Equipment7064620061109204031.jpg



Not essential but recommended: A sheet of grid paper to check the flatness. Be within range of a television, radio, etc for entertainment while your doing it. :D


http://slidog.bigblog.com.au/data/2/11934/image/gridpaper6971220061109200734.jpg



Sandpaper

You need some higher grade stuff than normal sandpaper. Some hardware stores might not stock the 2000 grit so your best bet is to phone around and find out who has what. If you can't find 2000 grit, just get as near to that as you can.

The prices that I paid ranged from 60 cents a sheet for the 400 grit up to $1.20 a sheet for the 2000 grit. I'd recommend getting around one or two sheets each of the 200, 400 and 600 grit as they last a while, 2 sheets of the 800 and 1200 grit, and 3 sheets of the 2000 grit stuff.

NOTE: If you're only going to lap a CPU then you probably don't need the 200 grit sand paper and probaly only 1 sheet of each because the CPU IHS covers are made from soft metal compared to heat sinks.


http://slidog.bigblog.com.au/data/2/11934/image/Sandpaper6968220061109200734.jpg



Secure the sheet down with tape. The rougher grade sandpaper will require duct tape but with the finer stuff like 1200 grit you can just use normal sticktape. As you can kind of see in this picture, I'm using an old mirror as the glass base.


http://slidog.bigblog.com.au/data/2/11934/image/tapingdown7066420061109205810.jpg



Lapping Technique

Place the surface to be lapped onto the sand paper and using both hands, gradually start to move the heat sink in a figure eight pattern. It may be difficult at first, particularly with the rougher grade paper, but it should become a steady flow soon enough. Make sure you keep the base flat to the surface and try to avoid letting the heat sink "shudder" across the paper. After a while you should start to see a pattern like this one emerge.


http://slidog.bigblog.com.au/data/2/11934/image/figure8wearpattern6971320061109200734.jpg


When you get a build up like this it's best to wipe the sand paper clean with an old rag. Just make sure that there is no debri on the paper before you start sanding again.



After a while the heat sink should start to slide easily as the sandpaper begins to wear out. You will also find that as this happens, the heat sink base will begin to smooth out. This is a good oportunity to take your gridded paper or a something similar (newspaper is good) and check your results so far.


600 grit surface - you can see how the edges still have the original surface texture indicating how uneven the surface was from the manufacturer.

http://slidog.bigblog.com.au/data/2/11934/image/600gritsurface26986920061109200734.jpg


600 grit reflection

http://slidog.bigblog.com.au/data/2/11934/image/600gritreflection6987020061109200734.jpg


800 grit surface

http://slidog.bigblog.com.au/data/2/11934/image/800gritsurface6987120061109200734.jpg


800 grit reflection

http://slidog.bigblog.com.au/data/2/11934/image/800gritreflection6988420061109200734.jpg


1200 grit surface

http://slidog.bigblog.com.au/data/2/11934/image/1200gritsurface6998020061109200734.jpg


1200 grit reflection

http://slidog.bigblog.com.au/data/2/11934/image/1200gritreflection6999120061109200734.jpg



And here is the finished product. You can see it's still not perfectly flat by the original surface showing on one of the edges but it's as flat as it's going to get without using a belt sander.


2000 grit surface

http://slidog.bigblog.com.au/data/2/11934/image/2000gritsurface17007720061109200734.jpg


2000 grit reflection

http://slidog.bigblog.com.au/data/2/11934/image/2000gritreflection47007620061109200734.jpg


[Main Page]
OCAU News
OCAU Forums
PC Database

Main Page
Recent changes
Random page
All pages
Help

View source
Discuss this page
Page history
What links here
Related changes

Special pages